SciCan Statim 2000 Manuel de l'opérateur télécharger pdf (Page 5)

6 7

2.3 - PUMP TESTER BOTTLE

(RPI PART #SCK024)

The RPI bottle has a “swivel fitting” on the lid that allows

you to control the position and balance of the bottle. In ad-

dition, RPI includes 8” of tubing already connected to the

swivel fitting which allows you to move the bottle a safe

distance away from the autoclave during testing.

The OEM now recommends the use of the Reservoir Cap &

Filter (RPI Part #SCK059) along with the In-Line Water Filter

(RPI Part #SCF034) on all units. The mesh filters should be re-

moved and the autoclave should be upgraded to the In-Line

Water Filter (Drain Kit with Pump Filter RPI Part #SCK037).

INSTRUCTIONS

STEP #1 - TO BEGIN: Disconnect the pump outlet meter-

ing tube (see Figure 2.3A) from the steam generator/

boiler by using a 3/8” wrench on the compression nut

while supporting the steam generator/boiler fitting with a

LL LI

NIMUM

Flow

290

7/16” wrench. Connect the metering tube to the Pump

Tester Bottle male connector and tighten.

STEP #2 - PRIME PUMP: Fill reservoir with distilled water

only and activate the pump for 2-3 seconds to purge any

trapped air from the tubing (until water passes through

the pump) (see page 5, 2.2 - Start Switch). Empty the

bottle of any water that may have entered it during the purge

cycle. The bottle must be completely empty before proceed-

ing with the test.

STEP #3 - TEST CYCLE: Before activating the pump for

the Test Cycle, have a stopwatch or another timing device

available for use during the Test Cycle. Activate the pump

and note the amount of time that it takes for the water

level in the bottle to reach the MINIMUM FILL LINE.

• If the water level reaches the MINIMUM FILL LINE within

25 seconds, pump testing is complete and no further

steps are required.

• If the water level does not reach the MINIMUM FILL LINE

within the specified time, proceed to the next step.

STEP #4 - FILTERS:

• If the autoclave has been upgraded with Drain Kit

with Pump Filter (RPI Part #SCK037), be sure to re-

move the mesh filter from both the inlet and outlet fit-

tings (if they have not already been removed). The ULKA

brand pump does not have the mesh filters. Replace the

Water Filter (In-Line) (RPI Part #SCF034). Repeat Step

#2 - Prime Pump, then if the water level still does not

reach the MINIMUM FILL LINE within 25 seconds, re-

place the pump.

• If the unit does not have the Drain Kit with Pump

Filter (RPI Part #SCK037) installed, then clamp off the

pump inlet tubing from the reservoir using hemostats or

a tubing clamp (Note: It is important to clamp the tubing

so that the reservoir does not drain). Disconnect the me-

tering tube from the pump. Remove the filtered elbow

outlet fitting and the filtered barb inlet fitting from the

pump. (Caution: Use a wrench on the pump body while

290

Flow

FIGURE 2.3B

TIP - If the unit does not have the

Drain Kit with Pump Filter (RPI

Part #SCK037) and the Reservoir

Cap & Filter (RPI Part #SCK059),

now is a good time to upgrade. If

time does not permit an upgrade,

remove and clean mesh filters

inside inlet and outlet fittings as

described above and anticipate

an upgrade at the next service.

removing filtered fittings). Clean the mesh filter of both

the inlet and the outlet fittings by placing the fittings

under running water, then blow both ends out with an air

hose. Reinstall the filtered fittings using Teflon® tape

(see Figure 2.3B). Be sure to prime the pump in order

to purge trapped air before running a complete cycle. If

the water level still does not reach the MINIMUM FILL

LINE within 25 seconds, replace the pump (see

Tip

Figure 2.3B). For additional information regarding the

pump see page 43 - Figure 9.6.

RELATED RPI PARTS

• Drain Kit with Pump Filter (RPI Part #SCK037)

• Metering Tube (RPI Part #SCT053)

• Reservoir Cap & Filter (RPI Part #SCK059)

• Teflon

Tape (RPI Part #RPT579)

• Water Filter (In-Line) (RPI Part #SCF034)

Drain Kit with Pump Filter

(RPI Part #SCK037);

Filter only (RPI Part #SCF034)

Metering Tube

(RPI Part #SCT053)

Reservoir Cap & Filter

(RPI Part #SCK059)

FIGURE 2.3A

TIP - The OEM now recommends the use

of the Reservoir Cap & Filter (RPI Part

#SCK059) along with the In-Line Water

Filter on all units. The mesh filters should

be removed and the autoclave should be

upgraded to the In-Line Water Filter (Drain

Kit with Pump Filter RPI Part #SCK037).

Bottle Male Connector

Bottle Inlet Tube (8”)

Pump Tester Bottle

(RPI Part #SCK024)

Inlet Fitting

Outlet Fitting

Metering Tube (RPI Part #SCT053)

to Steam Generator/Boiler

Mesh Filter

Reservoir

1 2 3 4 5 6 7 8 9 10 ... 28 29

Commentaires sur ces manuels

Pas de commentaire

SciCan Statim 2000 Manuel de l'opérateur Page 5

Commentaires sur ces manuels