SciCan Statim 2000 Manuel de l'opérateur télécharger pdf (Page 7)

10 11

2.6 - CASSETTE SEAL REMOVAL

TOOL (RPI PART #RPT372)

The Cassette Seal Removal Tool was designed to help

remove the cassette seal for either maintenance or

replacement without scratching the cassette lid or dam-

aging the seal.

INSTRUCTIONS

Slip the tip of the tool behind the seal at one of the corners

of the cassette and pry the seal loose (see Figure 2.6).

Once the first corner is free, take hold of the cassette seal

and pull down and out in order to remove it from the cas-

sette groove. The cassette seal and groove can now be in-

spected and cleaned. For additional information and tips,

see “Installation and Monthly Maintenance Guide”

that is supplied with RPI's Cassette Seals (RPI Part #'s

SCS001 & SCS029) or see page 22.

2.7 - LIQUID SOAP (4/PKG)

(RPI PART #RPS287)

The Liquid Soap comes in a convenient single-use foil

pouch that’s easy to store and use. It is recommended to

use the soap on the cassette seal for installation and reg-

ularly scheduled maintenance every 30 days.

INSTRUCTIONS

Open one package of Liquid Soap and lightly lubricate the

cassette seal using entire contents (see Figure 2.7). Dis-

pose of packet after use. The MSDS is available on the RPI

website (www.rpiparts.com).

RELATED RPI PARTS:

• Cassette Seal 2000 (RPI Part #SCS001)

• Cassette Seal 5000 (RPI Part #SCS029)

• Sci-Dry™ (2 oz. Spray Bottle) (RPI Part #SCA054)

For additional information and tips, see “Installation and

Monthly Maintenance Guide” that is supplied with RPI's

Cassette Seals (RPI Part #'s SCS001 & SCS029) or see

page 22.

FIGURE 2.7

TIP - lightly lubricate the cassette seal

using liquid soap at time of installation

as well as during regularly scheduled

maintenance every 30 days.

Liquid Soap

(RPI Part #RPS287)

FIGURE 2.6

TIP - Slip the tip of the Cassette

Removal Tool behind the seal at

one of the corners of the cassette

and pry the seal loose with ease.

Cassette Seal

STATIM 2000: (RPI Part #SCS001)

STATIM 5000: (RPI Part #SCS029)

Cassette Seal Removal Tool

(RPI Part #RPT372)

2.8 - THREADLOCKER 545

(RPI PART #RPA369)

Threadlocker 545 comes in a tube with a slender neck al-

lowing it to reach difficult areas, and the tube has a reuse-

able lid. It is for use on all pneumatic and hydraulic fittings

requiring a high temperature sealant and threadlocker.

INSTRUCTIONS

Clean threads, shake well and use 2-3 drops on the

threaded portion of a fitting to lock and seal. (Note:

Accommodates operating pressures up to 10,000 PSI and

temperatures ranging from -65˚F to 300˚F.) The MSDS is

available on the RPI website (www.rpiparts.com).

USE WITH RPI PARTS:

• Check Valve (RPI Part #SCK011)

• Male Connector (RPI Part #RPF227)

• Push-in Elbow Fitting (RPI Part #RPF363)

• Push-in Elbow Fitting (RPI Part #RPF377)

• Safety Valve (38 PSI) (RPI Part #SCV027)

• Safety Valve (70 PSI) (RPI Part #SCV004)

FIGURE 2.8

TIP - Use 2-3 drops of Thread-

locker 545 on the threaded portion

of a fitting to lock and seal.

Reuseable Lid

Threadlocker 545

(RPI Part #RPA369)

2.9 - HEX BALLDRIVER (9/64")

(RPI PART #RPT836)

The Hex Balldriver is designed to reach far into the auto-

clave to easily access the probe bracket mounting screws

for alignment or replacement without removing other com-

ponents. This job, without this long reach Balldriver, may

have required removal of the pump, steam generator/

boiler, and/or solenoid valve. This Balldriver will fit the OEM

or RPI probe bracket mounting hardware. See Figure 2.9.

Caution: Disconnect the power to the autoclave before

servicing and be sure the steam generator/boiler has

completely cooled.

RELATED RPI PARTS:

• Probe Bracket Kit 2000 (RPI Part #SCK038)

• Probe Bracket Kit 5000 (RPI Part #SCK042)

• Probe Bracket 2000 (RPI Part #SCB039)

• Probe Bracket 5000 (RPI Part #SCB043)

• Probe Bracket Gasket (RPI Part #SCG010)

FIGURE 2.9

TIP - If realigning existing probe bracket,

loosen (DO NOT REMOVE) 4 mounting screws

and compression fitting connections to allow

repositioning of probe bracket steam ports.

Thermocouple

(RPI Part #SCT030)

Hex Balldriver (9/64")

(RPI Part #RPT836)

Microswitch Kit

(RPI Part #SCK007)

Installed

Probe Bracket Kit

2000 (RPI Part #SCK038)

5000 (RPI Part #SCK042)

Probe Bracket

2000 (RPI Part #SCB039)

5000 (RPI Part #SCB043)

Probe

Bracket Gasket

(RPI Part #SCG010)

1 2 3 4 5 6 7 8 9 10 11 12 ... 28 29

Commentaires sur ces manuels

Pas de commentaire

SciCan Statim 2000 Manuel de l'opérateur Page 7

Commentaires sur ces manuels